The TGAM breakout boards arrived
This used gas mask looks really cool, it's slightly too small but I paid only 10 EUR for it...
Assembled paryhat, with velcro so i can convert it to more portable format as needed
RPI output on the coms console BW TV
Can't recall if the insides of our "geiger counter" have been photographed
Leftovers
The cut & bent reflector next to the diffuser
Making reflectors @Stadi Mallarit workshop
Building smart intervalometer rig.
Made two thumbnuts for 1/4" UNC thread (other shown with a short lenght of threadstock)
Vacuumbot
That went well...
Refletor test run Video: http://www.youtube.com/watch?v=GL4fTvC9zTU
Reflectors and LEDs glued with thermal glue
Cutting by hand leads to less-than-perfect but usable results
Making two reflectors
This will be a diffusor, but i need to figure a function for that curve...
One down, 13 to go...
Seen in Westend bus-stop
Testing idle sleep
Soldered two RGB leds to IDC cable connecting to the board
Two ultracaps in series for 5V 1300F goodness
Filing the bandsawed edges
Eyeballed measurements
How to get more power handling out of puny 0805 resistotrs ? Stack 'em
3 partyhatwork boardss with their XMegas
Making 3 XMega boards
Everything glued down
We have output
Added ATTiny85 as controller for the 7-segment LED sign, it takes ASCII orver I2C
Stock and modified for device power AVRISPmkII
The decoration assembled
Cool holiday decoration with LEDs inside
Made a cable breaking out mini-USB
Almost complete partyhatwork board
Soldering stacking headers to the XMega board
Partyhatwork board bottom
Patyhatwork board top
Oops....
Breaking out SOIC-20, dead-bug -style
ATTiny1634 breakout on breadboard (the chip itself is on the underside, dead-bug -style)
Powermeter in place
ATTiny84 driving LCD
Air-core shielding tubes in place (also visible the new switch wiring)
Jig for centering the shielding-tubes
The ATX adapter ready
Making ATX power supply adapter
The lid controller enclosed, the jack is for controlling a smoke machine
Preparing to enclose the "reactor lid" interface (Arduino Mega)
Inverting buffer (wing) for Arduino
80 RGB LEDS soldered
Patience and good preparations are the key here
Using my alu stock to keep the laptop from overheating
LANitunnelmaa
Jaron has "portable" lan rig
Schokakola cake
Ensiferum @Nosturi
Brymir on stage @Nosturi
New ATTiny breakouts (for 84 and 4313)
New batch of PCBs from Seeed Studio
These turned out a lot better than I expected
Switched the screws and engraved a picture on the underside
"Den" for my AVR Dragon, made from lasercut acrylic
ATTIny85s on the breakout board with 16MHz crystals
ATTiny85 breakout boards
Made a few QnD breakout/ISP boards for the ATTiny85s
Geiger counter v2 with ATTiny internals
5 boards done
Preparing to solder the SMD components on a preheater. First preheat to 100C and then using 290C hot-air to finish
One board with SMD components placed, 4 to go (a pick'n'place machine would be nice...)
New revision of the ATTiny based aircore driverboard
My prescioussss
ATTIny debugging continues
Cleaning up sawed edges
Another ATTiny test board
Testing the aircore-gauges with the full reactor simulator -stack
The I2C signals look a bit questionable but it still works...
Temporary Arduino installation to drive the 4 air-cores installed on this panel
Testing/debugging ATTiny based I2C controlled PWM driver
Setting up the "reactor simulator" @Camp Pixelache
Testing wiring of the reactor simulator "lid"
Endcap in place
Turned an endcap from PTFE
